Your shopping bag is empty
Go to the shopKeg Land
1/2 Inch BSP Stainless Hex Nipple
$3.95
A hex nipple is a fitting that is constructed from a piece of pipe that has a hexagonal section in the middle used for a pipe wrench to fit onto and used to tighten or loosen. These Hex Nipples are great quality
1/2inch Tap / Ball Valve with 13mm Barb
$21.95
Looking for a ball valve to attach some silicone hosing too? Then this is exactly what you need. Don't waste your time looking for 1/2" attachments with barbs, this has it already connected! Made from 304 Stainless Steel with a rubber covered handle. Comes with 1/2" Stainless Nut & Silicone Washer to seal. Please note silicone washer should be on the...
4 Tap T-Bar Brushed Stainless Font Kit
$225.95
If you're looking for the perfect addition to your Kegerator or Keezer set up, look no further than the simple T-Bar from KegLand. Mount 4 NukaTap - SS taps to this badboy with enough room for Bishop Tap Handles. Includes1 x 4 Tap T-Bar with Dust Cover Cap1 x Font Rubber Gasket4 x duotight compatible short shanks4 x 6.35mm x...
65L AlcoEngine Distillation Lid with 47mm hole
$34.95
Made from 304 grade stainless steel this large size lid. Also fits Digi boil or BrewZilla boilers and comes with silicone seal attached to ensure a complete seal when distilling.
7 In 1 Faucet Tap Wrench Spanner Tool
$5.95
EVERYONE SHOULD HAVE ONE! This hand and inexpensive tool is what every home brew kegger should have in the toolbox. It's really useful for all the most common fittings that you are likely to see in the draft beer world. This new 7 in 1 tool is also suitable for Duotight fittings and it's been improved since the older 5...
9.5lt Ball Lock Keg
$110.00
Widely referred to as the "Picnic Keg" or "Half Corny" the 9.5L is the ideal solution for small batch makers or those not wanting to lug a bigger keg around when travelling to share their brew with others.
AlcoEngine Pot Head
$0.00
Note: With Robobrew units you will need to purchase the KL03483 stainless lid with 47m hole. This is sold separately and is not included with the Robobrew unit. The stock glass lid that comes with the Robobrew unit will not be suitable. Features Lead free brass. Lead free silver soldering. High quality manufacture Super easy to use Australian Design
Barb Manifold Gas Line Splitter with Check Valves (1/4" thread, 6mm Barb)
$20.95
These gas manifolds are rated to 100psi and include 3 gas line outputs and 3 x 1/4inch ball vales. This unit can be turned into a 4 way manifold by adding a 1/4 inch ball valve. You can also attach a Gas Ball Lock Post with 1/4 Inch Bulkhead Assembly if you want to be able to easily disconnect/reconnect a gas...
Black Phantom Single Tap Stainless Font Kit
$62.95
The Black Phantom Font Kit is the perfect match for your Black Punisher or Stealth Bomber Nukataps. Made of high quality 304 stainless with a classy matte black finish, it is sure to add a touch of panache to your kegerator! This duotight font kit includes: Single Tap Black Punisher Stainless Font Only (includes gasket) 1 x duotight compatible Short...
Black Phantom Single Tap Stainless Font Only
$49.95
The Black Phantom Single Tap Stainless Font is quality made 304 grade stainless steel font with a Matte Black finish.
BrewZilla 35L - Gen.3.1.1
$445.00
The All-in-One Brewery alternative with re-circulation pump as standard. Dual Element Control (1900w & 500w) Step timing and delay start feature. The BrewZilla Also works great with our: Alcoengine Pot & Alcoengine Reflux Note: If you are using one of these stills with the BrewZilla you will require a different lid which can be purchased from us.
Brewzilla Gen 4 - 35lt
$650.00
The BrewZilla Gen 4 is designed to be a compact single vessel all grain home brewing system that can be run off a single 220-240v socket. A complete turnkey system with a delay timing feature and step mash functionality. Built to make batches up to 30L, it is the ideal solution for those who want to take the first step...
Calcium Chloride (Pickle Crisp) 50g
$3.50
Lowers Mash pHCalcium Chloride (CaCl2·2H2O) - Adjusts brewing water, accentuates maltness and lowers mash pH. Calcium adds to water hardness and chloride accentuates maltness, sweetness and fullness. Typical concentratons for brewing water are 50 – 150 ppm Ca2+ and 50 – 150 ppm Cl- . It is also used to lower the mash pH. Additons can be put in the brewing water or...
Carbonation Keg Lid with 0.5 Micron Diffusion Stone
$55.95
The keg lid with built-in carbonation stone! The easiest way to carbonate your beer.Move the lid from keg to keg to carbonate as needed. This lid allows fast force carbonation with the minimum of effort.Features:- Stainless Steel 0.5 Micron Diffusion Stone- Keg Lid with Stainless Ball Lock Post- Silicon Keg Lid seal- 60cm of hose
Compact Adjustable Magnetic Stirrer Machine
$59.95
If you're new to brewing you'll soon learn that healthy yeast makes better beer. The best place to start with making healthy yeast is to build up their numbers. We like to use Brewer's Friend's Yeast Calculator to find out how much yeast you need to build up to get the best possible beer fermented. In combination with a 1000mL, 3000mL or...
Cornelius Type Ball Lock Liquid Post
$10.95
1/2″ male liquid keg post complete, used on Mytton Rodd kegs.
Double Ended Ball Lock Keg Post
$5.95
This double ended cornelius post does not have a spring / poppet. It just has a piece of bar that activates the ball lock disconnect wide open.This double ended post will only work with liquid Ball Lock posts. e.g. The Premium Ball Lock in Black MFL and Barb, the Machined and Cast Stainless Steel disconnects in barb and MFL.
duotight - 9.5mm (3/8”) Female x 5/8” Female Thread
$6.95
Looking for high quality push in fittings that will seal tight? duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design. Why do we use Double O-rings?The secret to our superior sealing performance is not just the fact that we use high quality EPDM o-rings but also use two of them. The double...
duotight - 9.5mm (3/8”) Female x 9.5mm (3/8”) Female Joiner
$5.95
Looking for high quaility push in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design. Why do we use Double O-rings?The secret to our superior sealing performance is not just the fact that we use high quality EPDM o-rings but also use two of them. The double...
duotight 6.35mm (¼") x 8mm (5/16") Female Reducer
$5.95
Looking for high quaility push in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design. Why do we use Double O-rings?The secret to our superior sealing performance is not just the fact that we use high quality EPDM o-rings but also use two of them. The double...
duotight 8mm (5/16") x Ball Lock Disconnect (Grey+ Red/Gas)
$5.95
This all new ball lock disconnect sets a new bar! The integrated duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze! Made...
duotight 8mm (5/16") x Ball Lock Disconnect (Liquid)
$5.95
This all new ball lock disconnect sets a new bar! The integrated duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze! Made...
duotight 8mm (5/16) x 8mm (5/16) Push In Joiner - Female
$5.95
Looking for high quaility push in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design. Why do we use Double O-rings?The secret to our superior sealing performance is not just the fact that we use high quality EPDM o-rings but also use two of them. The double...
duotight 9.5mm (3/8) x Ball Lock Disconnect - Liquid
$5.95
This all new ball lock disconnect sets a new bar! The integrated duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze! Made...
duotight – 8mm (5/16”) Female x FFL Female Thread
$5.95
Looking for high quality push in fittings that will seal tight? duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design. Why do we use Double O-rings?The secret to our superior sealing performance is not just the fact that we use high quality EPDM o-rings but also use two of them. The double...
duotight – 8mm (5/16”) Female x ¼" BSP Male Thread (With Seated O-Ring)
$5.95
Looking for high quaility push in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design. Why do we use Double O-rings?The secret to our superior sealing performance is not just the fact that we use high quality EPDM o-rings but also use two of them. The double...
FermZilla Conical Jacket
$35.95
FermZilla Conical - 27L Jacket ~ Also Fits 60L All Rounder This jacket is designed to insulate your FermZilla during the colder months to keep your fermentation at the optimum temperature. It can also be used with a heating belt/wrap to warm up the wort if the heat from the fermentation isn't enough. Also completely blocks any light/UV to prevent light stuck...
FermZilla Plastic Pressure Kit
$21.95
Add this optional pressure kit to your FermZilla 27L or 55L and turn your FermZilla into a true uni tank. Uni tanks are conical fermenters used both for fermentation and for carbonating and serving finished beer. This extremely inexpensive upgrade will truly show you what the FermZilla was designed for. This kit contains: • 1 x Red Plastic Carbonation Cap • 1 x...
Food Grade Lubricant 28g
$5.95
Haynes Lubri-Film Plus is a heavy duty sanitary lubricant with extended performance and low friction properties.
Gauge Guard - Stainless Steel for MK4 Regulator (Bump Guard)
$19.95
Are you like us? Do you sometimes push in your Kegerator too hard against the wall with the gas bottle on the back? Maybe you've broken a dial in the process of dropping or transporting your gas bottle with the regulator attached. Or perhaps you're in a busy cafe/bar and someone needs to change over the tank and they drop...
Grain Mill 3 Roller
$230.00
The Grain Mill (3 Roller) is constructed using materials that will last a lifetime. Cold rolled steel for the rollers, 6061 Aluminum body and hopper with long lasting hardened steel bearings.The 3 roller design has the main advantage that it draws in the grain better and gives improved milling throughout.
Heating Element ~Stainless Steel
$45.95
These 304 Stainless 2200w Weld-Less Elements are designed to fit a 32mm Hole inside the wall of your brewing vessels or boilers. It does not come with the power cord (part code: KL03520). Attachment guide: Element goes inside vessel with washer attached, then push through the electrical cord through the 32mm hole. Then pull over large hex nut over the...